Users Manual - Fluke
Diode clamp. Do not apply external voltage; it may blow Your Fluke meter is designed to tolerate up to several volts of ac noise. Noise appears as changing numbers on If the display reads any other value, have the meter serviced. 4. ... Read More
Current clamp - Wikipedia, The Free Encyclopedia
(thousands of hertz) range. This type was often used with oscilloscopes, and with high-end A relatively recent development was a multi-conductor clamp meter with several sensor coils around the Less-expensive clamp meters use a rectifier circuit which actually reads mean ... Read Article
Common Measurement Errors - Part 1 - Stray Voltage, Phasor ...
Common Measurement Errors Part 1 5420 Glenway Circle Oregon, Wisconsin 53575 Phasor • To make sure your meter reads only AC volts when in the AC mode do the following: waveforms from 60 Hertz to over 1,000,000 Hertz ... Content Retrieval
User's Guide Extech EX830 True RMS 1000 Amp Clamp Meter With ...
Congratulations on your purchase of the Extech EX830 True RMS 1000A Clamp Meter. This meter measures AC/DC Voltage, AC/DC Current, Resistance, Hz Hertz (Frequency) oF and o The clamp meter LCD will display the reading. ... Fetch Here
Using A DVOM
Make sure to touch the metal contact inside the socket If the meter reads anything other than OL the fuse is good If the meter reads OL the fuse The unit of measure is in Hertz the Amp Clamp Incorrect Amps clamp setup Polarity arrow Meter maintenance Batteries ... Fetch Document
DCL-420 Man EN V3
DCL-420 is a True RMS Auto Ranging Clamp on meter with 3-3/4 digit 4000 count display. This meter can measure/test the following: – Voltage – Current – Resistance – Continuity – Temperature – Frequency Continuity Hz Hertz (Frequency) ... Visit Document
Multimeter Measurements On Variable Frequency Drives Using ...
Until now the only meter on the market able to make these measurements accurately was the Fluke 87V Digital Multimeter. Phase current reading + motor speed using i1010 clamp Fluke Corporation PO Box 9090, Everett, WA USA 98206 Fluke Europe B.V. PO Box 1186, 5602 BD Eindhoven, The Netherlands ... Read Content
Multimeter Measurements On Adjustable Speed Drives Utilizing ...
Meter can’t reliably read the output side of a because the ASD applies pulse width modulated non-sinusoidal voltage to the motor terminals. A true-rms DMM reads the heating effectof the non-sinusoidal voltage applied displayed reading in hertz will be the motor speed (see Figure 3 ... Fetch Here
X-HW 200 Hot Wire Power Supply Calibration TP-HW-001 Rev 3
HOT WIRE POWER SUPPLY CALIBRATION Doc. No.: TP-HW-001 Revision: 3 Page: 1 of 13 Place the FLUKE clamp-on meter on the Work lead from the Hot Wire Power Supply. 4.1.3. Connect the load bank to the output of the Hot Wire Power Supply. (The ... Read Here
CHAPTER 5 : POWER METERS - Life Long Learning, Through Technology
Figure 5.6 : Clamp Meter In electrical and electronic engineering, Less-expensive clamp meters use a rectifier circuit which actually reads mean current, (thousands of hertz) range. This type is often used ... Access Doc
Cplus.about.com
Citer cites city civet civic civie civil civvy clach clack clad clade clads clag clags claim clam clamp clams clan clang clank clans clap claps clapt herry hers hertz hes hest hests het heth heths mete meted meter metes meth meths metis metol ... Read Article
MEASURING SYSTEMS AND TOOLS
CAT IV CAT IV meters are for clamp-on meters only. If a clamp-on meter also has meter leads for voltage • Diode check Additional features for advanced automotive diagnosis include: • Frequency (hertz, abbreviated Hz) • Temperature The meter reads the voltage ... Fetch Document
DIGIT & POINTER MULTIMETER
Digital Clamp Meter User [s Manual Table of Contents LIMITED WARRANTY AND LIMITATION USING THE METER ..10 Display Hold.. 10 Manual Measurement.. 10 Frequency and Duty Ratio ... Read More
Harborfrite95670meter - YouTube
This is the meter I've been speaking about being used as a Low Freq counter for tuning generators. The 20 Khz (20,000 Hz) setting is a bit too buggy and only This is the meter I've been speaking about being used as a Low Freq counter for tuning generators. ... View Video
Testers And Meters - Testing Electrical Circuits
Testing electrical circuits is a must when they go on the fritz. Knowing how they work and how to test for power will help you track down the problem. ... Read Article
Instruments & Test Equipment
Also indicates an open phase. 60-600 volts, 25-60 Hertz. • Reads ground resistance down to 0.10Ω. H. AC Clamp-On Meter - Both AC amperage and voltage measurement, resistance up to 2kΩ, 2000-count LCD display. SPECIFICATIONS ... Retrieve Here
Basic Power Quality Measurements On The Go With The Fluke 345
A clamp meter, power quality meter, oscilloscope, and data logger in one. This combination of functions, (Hertz) or 50 Hz in some parts of the world. This is called the fundamental frequency of the system, or the first harmonic. ... Read Full Source
Instrument Basics - For Your Information
Instrument Basics and Common Measurement Errors March 2003 • To make sure your meter reads only AC volts when in the AC mode do the following: 100 Hertz to 2,000,000 Hertz. Instrument Basics and Common Measurement Errors March 2003 ... Fetch Content
Basic Power Quality Measurements On The Go With The Fluke 345
Basic power quality measurements on the go with the Fluke 345 Waveform view The world runs on ac voltage, The Fluke 345 combines a clamp meter, power quality meter, oscilloscope, and data logger in one. (Hertz) or 50 Hz in some parts of the world. ... Access This Document
Multimeter - Wikipedia, The Free Encyclopedia
An un-amplified analog multimeter combines a meter movement, usually a small constant current is passed through the device under test and the digital multimeter reads the resultant Clamp meters clamp around a conductor carrying a current to measure without the need to connect the ... Read Article
Basic Power Quality Measurements On The Go With The Fluke 345
Basic power quality measurements on the go with the Fluke 345 current is present. When that happens, the standard clamp meter isn’t going to get the job done. The solu-tion may be a power quality clamp meter such as The Fluke 345 reads these parameters in both single-phase and balanced ... Document Viewer
Testing Electrical Systems With A Digital Multimeter
Testing Electrical Systems with a Digital Multimeter Perhaps the most important tool you'll use in troubleshooting auto electrical systems is the multimeter. ... Read Content
No comments:
Post a Comment